60 Hz
60 Hz
.
Potentiometer for regulating a fan using a 0-10V recessed signal
| Multiple control unit for Vortice HVLS HYPERBLADE ceiling fans. It allows the control of up to 20 fans in manual or automatic mode, depending on the temperature measured by the integrated sensor or the wind speed measured by the WP anemometer. Single-phase 230 V / 50 Hz power. Casing for wall installation. |
| External anemometer to be connected to the VORT T control unit, useful for the automatic control of the ceiling-fan in case of wind gusts. |
Modbus USB converter compatible with VORT T control unit, useful for remote control of single or multiple ceiling-fans.
Pole, length 3 or 6 meters, for installation on high ceilings.
Relative Humidity sensor (RH) that can be combined with the VORT T-HCS and VORT T PLUS control units.
Temperature probe that can be combined with VORT T, VORT T-HCS and VORT T PLUS control units.
F-RS485 (COD. 20751)
RC interference filter (DIN rail housing) for VORT T PLUS control unit.
F-RS485 DIN (COD. 20752)
DIN rail mounted RC interference filter for VORT T PLUS control unit.
F-RS485 (COD. 20751)
RC interference filter (DIN rail housing) for VORT T PLUS control unit.
F-RS485 DIN (COD. 20752)
DIN rail mounted RC interference filter for VORT T PLUS control unit.
Specifically designed for the zootechnical industry, the VORT T-HCS control unit is an optional, wire-connected control device with an LCD display, capable of automatically monitor the fans connected based on temperature values, relative humidity, and THI (Temperature Humidity Index), the bioclimatic index that combines the simultaneous effect of temperature and relative humidity and is used to determine heat-induced stress in the livestock. VORT T-HCS allows the automatic management (ON/OFF up to 4 strokes) of the optionally installed cylinders, the limitation or interruption of the ventilation upon start, and the management of the auxiliary ventilation sytems, if any. Alternatively, fan speed and cylinder control can be manually adjusted, regardless of climatic conditions, e.g. for testing the proper functioning of the system during installation or trial.
Vort T-PLUS is a device specifically designed for the accurate control of the microclimate of livestock farms. The onboard microcontroller (PLC) has an intuitive user interface with an 8-keys keypad and allows, the sequential programming of the operation of the individual devices installed according to the values of temperature, humidity and wind speed detected. In particular, VORT T-PLUS: • Controls the wind speed, stopping ventilation in case of need/opportunity; • Manages the ventilation intensity, operating (0 to 10-V signal) the EC motors of the connected fans; • Detects temperature and THI values; • Controls up to 4 cylinders with 4 on-off programmable levels; • Controls humidity by blocking cylinder commands, if needed; • Manages temperature and THI alarms; • Allows hourly programmation. • Communicates with VORT MASTER through the integrated RS-485 port The enclosure, in the standard DIN 9 module format, simplifies its installation inside switchboards. The 8-segment display is easily readable; the operating states of the connected products are represented by special LEDs.
Specifically designed to be used in the zootechnical industry, the VORT MASTER control unit guarantees the monitoring of the microclimate in cattle breeding facilities (up to 12 areas and 12 lines) by managing each fan, cylinder, (temperature and amperometric) alarms based on temperature, humidity, THI, air speed, and other values detected by the sensors installed. It is also possible to programme functioning hours and durations for the shutdown of utilities. The graphical interface of the touch LCD panel facilitates real-time control of the correct operation of the system. A password ensures unwanted, while an adequate internal storage space allows consumption analysis, storage of operating data and recording (datalogging) of events. A USB port also allows connection to a camera. Through the ethernet port, VORT MASTER can be connected to a network and remotely controlled; at the same time, the VNC (Virtual Network Computing) technology allows its quick and easy connection to smartphones, tablets, and personal computers.
Digital potentiometer for regulating the operating speed of NORDIK HVLS industrial fans. Fans speed percentage adjustment (settable value: from 0% to 100% / OUTPUT: 0-10V). Reverse mode activation («R.V» button). Switching off (‘OFF’ displayed on screen): the connected fans stop (speed value=0%). Operating temperature: -10...+55°C.
Pivot vertical axis rotation system
Pole, length 3 or 6 meters, for installation on high ceilings.
Beam mounting kit with the possibility of horizontal and vertical orientation.
Fan fixing kit on beams with a thickness between 180mm and 300mm. Made of S355 structural steel, it allows the setting of alternative angles of inclination of the fan with respect to the horizontal (20°, 30°, or 45°) and vertical (angle: 15°,30°, or 45°) axes at various adjustable angles to orient the product along the vertical and horizontal axes.
'+39 90 699 1